Key Takeaways

  • No national law sets a closing time for a factory or warehouse in Malaysia. A lawfully approved unit in a designated industrial area can run 24 hours if its noise, loading and staffing stay within the rules below.
  • What usually stops night work is noise at the nearest neighbour. The Department of Environment (DOE) guideline treats 10.00 pm to 7.00 am as night and, for existing built-up areas, recommends 75 dBA at an industrial receiver but 60 dBA at suburban or urban homes and 55 dBA at low-density homes, schools, hospitals and places of worship.
  • The standard industrial licence conditions published by MBDK (Klang) and MBSJ (Subang Jaya) do not fix operating hours, but they ban noise that becomes a nuisance, work or goods outside the premises, and using the factory as living quarters.
  • Loading inside your own compound can run through the night; loading on the road, five-foot way or parking bays needs council permission. Heavy lorries are barred from parts of PLUS, NKVE, ELITE and DUKE at weekday peak hours, which pushes more deliveries into the night.
  • Shift workers may work more than 8 hours a day only if their hours average no more than 45 a week over three weeks, and never more than 12 hours in a day; overtime is capped at 104 hours a month.

Can a factory or warehouse legally run 24 hours in Malaysia?

Yes, in most cases. Neither the Employment Act 1955, the Environmental Quality Act 1974 nor the standard industrial licence conditions we read from Selangor councils sets a closing time for an approved factory or warehouse. A plant may run round the clock as long as it passes four separate tests, each owned by a different authority:

Test Authority What decides it
Noise at the boundary and at neighbours DOE and the local council Land use of the nearest receiver; stricter limits from 10.00 pm
Licence and planning conditions Local council (MBDK, MBSA, MBSJ, MBPJ and others) Conditions written on your licence or planning approval
Shift hours, rest days and overtime Labour Department (JTKSM) Employment Act 1955 and its regulations
Trucks reaching and leaving the site LLM, JPJ and the council Highway peak-hour bans, festive road bans, loading on public roads

Where the answer depends on the unit, the deciding factor is almost always who sits next door and what the unit's own licence or planning approval says. A detached factory in the middle of an established industrial estate and a terrace factory whose back wall faces a housing estate can carry very different risks under the same council.

What are the DOE noise limits for factories at night?

The DOE's Guidelines for Environmental Noise Limits and Control, Third Edition 2019 recommend limits by the land use of the receiving property, measured outdoors at the receiver's boundary. Day is 7.00 am to 10.00 pm and night is 10.00 pm to 7.00 am. For industrial noise in an industrial zone, the measurement may be taken at the property boundary of the plant itself.

Limits for existing built-up areas (Second Schedule)

The guideline calls this schedule "a more practical limit in most applications" for developed, populated areas, which describes most Klang Valley industrial estates.

Receiving land use Day LAeq (7 am to 10 pm) Night LAeq (10 pm to 7 am)
Low-density residential, schools, hospitals, places of worship 60 dBA 55 dBA
Suburban and urban residential, mixed development 65 dBA 60 dBA
Commercial business zones 70 dBA 65 dBA
Industrial zones 75 dBA 75 dBA

Limits for planning and new development (First Schedule)

For new industrial, commercial or housing areas the targets are stricter: 70 dBA by day and 65 dBA at night for industrial zones, 60 and 55 dBA for suburban residential areas, and 55 and 50 dBA for low-density housing and noise-sensitive receptors. Where night noise is already above the Second Schedule figure, the Third Schedule asks that a new source keep it at the existing level, within 1.5 dBA.

Why night is the real test

Two features of the guideline matter more than the headline figures. First, an industrial receiver keeps the same 75 dBA limit day and night, while every residential category drops by 5 dBA after 10.00 pm. Second, the guideline's assessment annex, drawing on BS 4142, says noise around 10 dB above the background level means complaints are likely, and adds a 5 dB penalty for tonal noise (a whine) or impulsive noise (bangs). Background noise falls at night, so a compressor, chiller, reversing alarm or dropped steel plate that nobody notices at 3.00 pm can draw complaints at 2.00 am.

What happens if you exceed the limits

Section 23 of the Environmental Quality Act 1974 bars emitting noise in breach of the acceptable conditions. Since the Environmental Quality (Amendment) Act 2024 came into force on 7 July 2024 under P.U.(B) 243/2024 (Skrine alert), the penalty is a fine of RM10,000 to RM250,000, jail of up to five years or both, plus up to RM1,000 a day if the offence continues after a DOE notice to stop. The DOE guideline adds that councils can act against premises whose noise is a nuisance under the Local Government Act 1976, and may now use the guideline's limits to judge it.

Where can a factory run 24 hours?

A factory runs 24 hours most comfortably where every neighbour within earshot is also industrial, because the night limit at an industrial receiver stays at 75 dBA. The closer the nearest home, school, hospital or place of worship, the tighter the night limit, falling to 60 dBA at an urban or suburban home and 55 dBA at a low-density home or sensitive building.

What decides it for a specific unit

  • The nearest receiver, not your own title. An industrial lot next to a housing estate is still judged at the houses' boundary.
  • Position within the estate. Inner lots surrounded by other factories carry less risk than end lots, corner lots or lots on the edge facing a taman.
  • Building type. In a terrace factory row your neighbours share walls and loading lanes; a semi-detached or detached unit leaves more room for setbacks, barriers and enclosed loading bays.
  • Your own process. Steady fans, tonal pumps and impulsive work such as stamping, metal cutting or container handling behave very differently at night.
  • Zoning and buffer zones. Which class of industry a site can take, and how far it must sit from housing, is set at the planning stage; see our guide to light, medium and heavy industry zoning and buffer zones.

The DOE guideline's own list of noise measures runs from land use compatibility, distance and barriers, through engineering controls such as building enclosures, to "limiting the operating time of noise source(s)". That last measure is what an authority reaches for when a plant near homes keeps drawing complaints, so the safest 24-hour site is one where it never comes to that.

A technician measures night noise at a factory fence facing a row of terrace houses
IllustrationA technician measures night noise at a factory fence facing a row of terrace houses

Does the council licence restrict operating hours?

Usually not in writing, but it controls everything that makes night work possible. The MBDK's industrial licence conditions for factories, warehouses and scrap premises in Klang set no closing time. They do require that:

  • industrial activity is carried on inside the premises only;
  • no goods or obstructions sit outside the premises, on the five-foot way, traffic islands, parking bays or other public areas without council permission;
  • the licence holder makes no noise that becomes a nuisance, and lets no dust, vapour, heat, gas, odour, vibration, smoke or soot become a nuisance;
  • the industrial premises are not used as private living quarters.

MBSJ's guideline for factory, industry and warehouse licences in Subang Jaya likewise bars work or goods on five-foot ways, lanes, roads, drains and entrances without permission and says nothing about hours. Breaches can bring a warning, a compound, seizure, closure of the premises, or suspension and cancellation of the licence, according to MBSJ's compliance conditions for general trade licences, which quote a by-law fine of up to RM2,000, jail of up to one year or both, plus RM200 a day for a continuing offence.

Two points for a buyer or tenant planning round-the-clock work:

  1. Read the unit's own documents. A council can attach a condition to a particular licence or planning permission, especially next to housing. Ask for the current business licence and the planning approval (Kebenaran Merancang) for the lot, and ask the licensing department in writing whether any hours condition applies.
  2. Night crews cannot sleep in the factory. The "no private accommodation" condition means night-shift workers need proper housing away from the production floor.

For the application itself, see our guide to the business premise licence for a factory or warehouse.

Can loading and unloading go on 24 hours?

Inside your own compound, yes, within the same noise limits. On public space, only with council permission. On the highways, part of the timetable is now set for you.

Loading inside the compound vs on the road

Council conditions in Klang and Subang Jaya keep loading, goods and work within the premises; using the road, the five-foot way, parking bays or drains needs permission. For shop and office premises, MBSJ's general trade conditions go further and fix loading times on weekdays: lorries of 1 tonne or more load at the back lane from 8.00 am to 6.00 pm and in front of the premises from 6.00 pm to 8.00 am. A unit in a mixed shophouse and light industrial row can fall under rules like these, so check which licence category it holds.

Why night loading draws complaints

Reversing alarms are tonal, while tailgates, roller shutters, container twist locks and forklifts crossing steel dock plates are impulsive, so each attracts the guideline's 5 dB penalty when judged against background noise. The usual fixes are an enclosed or covered loading bay facing away from housing, broadband reversing alarms, rubber dock bumpers and a no-idling rule for waiting trucks. A unit whose loading bay faces a residential boundary is a risk for night logistics however good the rest of the building is. Check gate width, turning space and dock height in our container truck access and loading bay guide.

Highway peak-hour bans push trucks into the night

Since 19 February 2025, Class 2 (two axles, six wheels) and Class 3 (three axles or more) heavy vehicles have been barred on weekdays, except public holidays, from 6.30 am to 9.30 am and from 4.30 pm to 7.30 pm on selected stretches: PLUS between Sungai Buloh and Bukit Lanjan, the NKVE between Shah Alam and Jalan Duta, ELITE between Shah Alam and Bandar Saujana Putra, and the whole of DUKE, Bernama reported citing the Malaysian Highway Authority (LLM). Warehouses serving Kuala Lumpur therefore see more early-morning and late-evening arrivals, which is exactly when the night noise limits start to bite.

Festive road bans

JPJ also bars heavy goods vehicles on set festive days. For Chinese New Year 2026 the ban ran all day on 14 to 15 and 21 to 22 February 2026 and covered, among others, carrier and tipper lorries over 7,500 kg laden, low loaders, pole and platform trailers, mobile cranes and cement mixers (MOT and JPJ notice). A 24-hour warehouse should plan stock and dispatch around these dates.

What does the Employment Act say about shift work and night shifts?

Round-the-clock staffing is legal as long as the roster follows Part XII of the Employment Act 1955. The Act defines shift work as work that by its nature must be carried on continuously or continually by two or more shifts.

Rule Day workers Shift workers
Hours a day 8 (s.60A(1)(b)) More than 8 allowed, never more than 12 (s.60C)
Hours a week 45 (s.60A(1)(d)) More than 45 allowed if the average over any three weeks is 45 or less (s.60C(1))
Break 30 minutes after 5 consecutive hours (s.60A(1)(a)) Same
Rest day One whole day a week (s.59(1)) Any continuous 30 hours counts as the rest day (s.59(1A))
Overtime pay At least 1.5 times the hourly rate (s.60A(3)) Same
Overtime cap 104 hours a month (Overtime Regulations 1980) Same

Points that trip up 24-hour operators:

  • The 12-hour ceiling is firm. It can be passed only for accidents, work essential to the life of the community or to defence and security, urgent work on machinery or plant, and interruptions that could not be foreseen (s.60A(2) and s.60C(2)).
  • The three-week average lets a roster swing between long and short weeks, but over any three weeks the total cannot pass 135 hours. A longer averaging period needs the Director General's approval.
  • Rest-day rosters must be issued before the month begins (s.59(2)).
  • Women on night shifts. The old Part VIII rules on women's employment, sections 34 to 36, were deleted by the Employment (Amendment) Act 2022 (Act A1651), as the August 2023 reprint shows.
  • Who is covered. Employees earning more than RM4,000 a month lose some provisions, including overtime pay under s.60A(3), unless they fall in a First Schedule category covered whatever they earn, such as manual labourers.
  • Overtime on 12-hour shifts. How a long shift splits between normal hours and overtime depends on the contract, so have the roster checked by your HR adviser or JTKSM before committing to a two-shift or three-shift pattern.

Noise exposure on long shifts

Separate from the neighbours, DOSH protects your own workers. Under the Occupational Safety and Health (Noise Exposure) Regulations 2019, "excessive noise" means a daily exposure above 82 dB(A), a daily noise dose above 50%, a maximum above 115 dB(A) at any time or a peak above 140 dB(C), as defined in DOSH's industry code of practice. Exposure is normalised to an 8-hour day, so a longer shift at the same sound level counts higher: the code's own worked example turns 87 dB(A) over 10 hours into 88 dB(A). The code also suggests running the noisiest machines on shifts with fewer workers present.

A lorry pulls into a covered loading bay inside a walled warehouse compound at night
IllustrationA lorry pulls into a covered loading bay inside a walled warehouse compound at night

How do you check a factory before signing for 24-hour use?

Do these before the letter of offer, not after the tenancy or SPA is signed.

  1. Visit at night. Stand at the boundary between 10.00 pm and midnight, note the nearest homes, schools, hospitals and places of worship, and listen to what the estate already sounds like.
  2. Map the receivers. Note the land use on every side of the lot; it decides which night limit applies.
  3. Get the documents. Ask the landlord or seller for the current business licence, the planning approval and any DOE approvals for the lot, and read every condition. Confirm with the council's licensing department in writing whether any hours or loading condition applies.
  4. Ask about complaints. Ask the council, the management office of a managed park and the neighbouring occupiers whether night noise complaints have been made against the unit or its previous occupier.
  5. Commission a baseline noise survey. An acoustic consultant can measure day and night LAeq and L90 at the boundary and at the nearest receivers using the DOE guideline's methods before your machines arrive. It becomes your benchmark if a complaint comes later.
  6. Check the truck route. Map the route to the port and customers against the peak-hour highway bans, and confirm the gate, turning space and loading bay take night arrivals without trucks queueing on the road.
  7. Check the power and the tariff. Under TNB's Time of Use tariff, peak is 2.00 pm to 10.00 pm on weekdays, the rest of the weekday and all of Saturday and Sunday are off-peak, and for medium and high voltage customers maximum demand that occurs in off-peak hours is not charged. A night-heavy plant can gain; see our TNB ToU guide for factories and size the load with the factory power calculator.
  8. Write it into the deal. Ask for the permitted use and operating hours to be stated in the tenancy or SPA, the landlord's help with licence applications, the right to install acoustic enclosures and barriers, and what happens if an authority later restricts hours.

This guide summarises public rules for planning purposes and is not legal advice; confirm your own case with the council, DOE, JTKSM or a lawyer.

Practical steps: more questions

Is electricity cheaper at night for a factory?

On TNB's Time of Use tariff, yes: weekdays from 10.00 pm to 2.00 pm and all of the weekend are off-peak, and medium and high voltage customers pay no maximum demand charge for demand set in off-peak hours. Whether switching saves money depends on how much of your load falls in the 2.00 pm to 10.00 pm peak.

Running nights in Klang? Ms Teh Seok Hoon covers noise, loading and shifts on a Klang estate; Jason Low sets out the night noise limits for Rawang and Shah Alam.

Frequently Asked Questions

Where can I find a logistics warehouse near Port Klang that can operate 24 hours?

Look for a unit deep inside an industrial estate near the terminal you use: Pulau Indah, PKFZ and Telok Gong for Westports, or Bandar Sultan Suleiman, Kapar and Meru for Northport. No law sets a closing time, but night noise decides it: the DOE guideline allows 75 dBA at an industrial neighbour from 10 pm to 7 am, against 60 dBA at urban homes. So avoid end lots or loading bays facing housing, load inside your own compound and read the council licence conditions. Peter Tan (016-666 6872) or Jason Low (012-288 1834) can shortlist units.

What is the acceptable noise level in Malaysia at night?

For existing built-up areas, the DOE guideline recommends night limits (10.00 pm to 7.00 am) of 55 dBA for low-density housing and sensitive buildings, 60 dBA for suburban and urban housing, 65 dBA for commercial zones and 75 dBA for industrial zones, measured at the receiver's boundary. New developments are planned to stricter figures, such as 65 dBA at night for industrial zones.

What time counts as night time for factory noise in Malaysia?

The DOE guideline treats 10.00 pm to 7.00 am as night and 7.00 am to 10.00 pm as day. It adds an evening period from 7.00 pm to 10.00 pm only for construction noise; factory operations are judged on the day and night split.

Do I need a special licence to run my factory 24 hours?

Not under the standard conditions we checked: the MBDK and MBSJ industrial licences do not set operating hours. You still need a valid business premise licence for the activity, and you must follow any condition written on your own licence or planning approval, so ask the council in writing before you sign.

Can workers sleep inside the factory during night shifts?

No. MBDK's industrial licence conditions bar using industrial premises as private living quarters, so night crews need proper accommodation away from the production floor. Plan transport and housing as part of the cost of a 24-hour operation.

Can female workers work the night shift in a Malaysian factory?

The Employment Act no longer has a separate part restricting women's work at night: sections 34 to 36 were deleted by the Employment (Amendment) Act 2022. The same shift, rest day and overtime rules apply to every employee the Act covers.

A shift worker may work more than 8 hours a day and more than 45 hours in a week, as long as the average over three weeks does not exceed 45 hours a week and no day exceeds 12 hours. Overtime is paid at no less than 1.5 times the hourly rate and is capped at 104 hours a month.

What is the fine for factory noise pollution in Malaysia?

Under section 23 of the Environmental Quality Act 1974, as amended from 7 July 2024, the fine is RM10,000 to RM250,000, jail of up to five years or both, plus up to RM1,000 a day if the noise continues after a DOE notice. Councils can separately compound, close or cancel the licence of premises whose noise is a nuisance.

FactoryHub is dedicated to helping every client find the right factory or warehouse. If you need a unit that can run around the clock in Klang, Port Klang or elsewhere in Selangor, call Peter Tan (REN 12771) at 016-666 6872 or Jason Low (PEA 1478) at 012-288 1834.