Key Takeaways
- A 40 ft container is 12.192 m long and 2.438 m wide. A standard box is 2.591 m high and a high cube is 2.896 m. The truck is much longer: the semi-trailer design vehicle in JKR's road design guide is 16.7 m long with a minimum turning radius of 13.7 m.
- PLANMalaysia's parking guideline sizes a trailer bay at 4 m x 18 m and adds 18.3 m for manoeuvring, so a trailer needs about 36.3 m of clear length at the spot where it loads.
- Selangor's planning manual sets a goods loading area of at least 9.144 m x 7.924 m, and a trailer bay of 4.267 m x 17.983 m plus 18.288 m for handling.
- Where trucks stand under a roof or canopy, PLANMalaysia asks for at least 4.5 m of headroom on level ground and 4.75 m on a ramp.
- At a viewing, measure the road kerb to kerb, the gate's clear opening and headroom, the yard depth in front of the loading door and every obstacle in the turn. Then ask your haulier to run the route before you sign.
Whether a 40 ft container truck can serve a factory or warehouse comes down to four things: the road outside, the gate, the yard in front of the loading door and the door itself. A listing that says "container access" does not tell you which of the four will fail. This guide puts the official numbers for 20 ft and 40 ft containers in one place and shows what to measure when you view a unit in Klang, Port Klang or anywhere else in Selangor. It covers access only; for dock levellers, clear height, cranes and floor loading, see our factory specs guide.
How big is a 20 ft or 40 ft container, and how long is the truck?
Container sizes
Container sizes are set by the ISO 668 standard. The container specification published by Hapag-Lloyd lists the external sizes and the minimum door openings:
| Container | Length | Width | Height | Minimum door opening (width x height) |
|---|---|---|---|---|
| 20 ft standard | 6.058 m | 2.438 m | 2.591 m | 2.337 m x 2.261 m |
| 40 ft standard | 12.192 m | 2.438 m | 2.591 m | 2.337 m x 2.261 m |
| 40 ft high cube | 12.192 m | 2.438 m | 2.896 m | 2.337 m x 2.565 m |
| 45 ft high cube | 13.716 m | 2.438 m | 2.896 m | 2.337 m x 2.565 m |
The same document rates Hapag-Lloyd's general purpose 20 ft and 40 ft boxes at up to 32,500 kg gross. One 40 ft series it lists has a tare of 3,700 kg and a payload of 28,800 kg. Your yard, the drain crossing at the gate and the road outside all carry that weight plus the truck.
Truck length
The box is only part of the length. JKR's road geometric design guide, Arahan Teknik (Jalan) 8/86, uses three design vehicles, and the longest of the three is the WB-50 semi-trailer combination. A 2017 paper in the Journal of the Society of Automotive Engineers Malaysia summarises it: 16.7 m long, a minimum turning radius of 13.7 m and an inside radius of 6.0 m. The WB-50 trailer is 13.0 m long, which a US design vehicle review groups with 40 ft (12.2 m) and 45 ft (13.7 m) trailers. That makes it a fair stand-in for a prime mover pulling a 40 ft container.
Trailers are getting longer, not shorter. On 12 March 2026 the Ministry of Transport conditionally approved open-platform semi-trailers with twist locks, reported by RTM: up to 45 ft including the twist-lock system, carrying only 40 ft and 45 ft ISO containers, with a maximum laden weight of 53 tonnes, for port-to-business and business-to-port runs. If your haulier may send one, plan for it.
A 20 ft container does not mean a small truck. It still arrives behind a prime mover, and the haulier picks the trailer. Ask which trailer they use on your lane and plan for the longest one.
How much turning space does a container truck need?
The turning circle
A 13.7 m minimum turning radius means the outer front corner sweeps a circle about 27.4 m across. Meanwhile the inner rear wheels cut in to about 6.0 m from the centre of the turn. In a tight turn the truck therefore occupies a band roughly 7.7 m wide, three times the 2.438 m width of the container. That band is what has to stay clear of kerbs, posts, drains and parked cars.
Planning rules give the same picture. Selangor's Manual Garis Panduan dan Piawaian Perancangan (fourth edition, 2022) says dead ends should be avoided in industrial areas; where a cul-de-sac is built, it may be no longer than 190.5 m and must end in a turning circle more than 30.48 m (100 ft) across. PLANMalaysia's parking guideline GP0011-A asks for the same 30 m circle where trailer parking sits on a dead end. So if a truck must turn round inside your compound, you need an open area about 30 m across. Few factory yards have that, which is why most trucks either reverse in from the road or drive through a compound with two gates.
The road outside
The Selangor manual sets industrial service roads at 20.116 m (66 ft), and side lanes, fire breaks and back lanes at 12.192 m (40 ft). These are road reserves. They include drains, verges and walkways, so the carriageway a truck can use is narrower. Measure kerb to kerb, then look at what is parked on both sides; parked trailers decide the real width. GP0011-A also says lorry and trailer parking areas should connect to a main road with a reserve of at least 30.5 m, ideally a dual carriageway.
Why the truck reverses in
A container's doors are at one end. To stuff or empty it through the doors, the driver has to bring the door end to your loading point, which usually means reversing in from the road. A narrow road with lorries parked opposite turns that into a long multi-point turn across both lanes.
How wide and how high should the gate be?
No figure that applies to every private factory gate turned up in the guidelines reviewed here, so use benchmarks. PLANMalaysia's heavy vehicle terminal guideline GP026 gives terminal entrances and exits a width of 12.0 m, for sites that take heavy trucks all day. A factory gate is usually narrower, and it works only if the road is wide enough for the truck to line up before it turns. The narrower the road, the wider the gate has to be.
What to check at the gate
- Clear opening: measure between the posts with the gate fully open, not the gate leaf. A sliding gate's end post and track, or a swing gate that cannot open fully, can take a metre off.
- Headroom: anything over the gate (a beam, signboard frame, cables, branches) must clear the loaded truck. A high cube box is 2.896 m tall before you add the trailer deck, so ask your haulier for the total height of their loaded high cube. PLANMalaysia uses 4.5 m of headroom on level ground and 4.75 m on ramps for lorry parking under cover, and GP026 sets canopy clearance at no less than 4.25 m (14 ft).
- The drain crossing: the culvert over the monsoon drain is often narrower than the gate. Its width and its condition decide what can cross.
How deep should the yard be in front of the loading bay?
Bay and manoeuvring space
| Guideline | Trailer bay | Extra space for manoeuvring |
|---|---|---|
| PLANMalaysia GP0011-A | 4 m x 18 m | 18.3 m (36.3 m in total) |
| Selangor manual, 4th edition | 4.267 m x 17.983 m | 18.288 m |
| Selangor manual, small lorry | 3.048 m x 6.096 m | 6.096 m |
The Selangor manual also sets a minimum goods loading area of 9.144 m x 7.924 m. GP0011-A suggests at least two loading spaces so trucks do not queue.
Apron depth by bay width
GP026 gives the apron, the clear space a truck needs at right angles to the dock face, for different vehicle lengths and bay widths. Note that the length here is the whole truck, not the container:
| Overall truck length | 3.06 m (10 ft) bays | 3.65 m (12 ft) bays | 4.25 m (14 ft) bays |
|---|---|---|---|
| 12.2 m (40 ft) | 14.0 m | 13.1 m | 11.9 m |
| 15.2 m (50 ft) | 18.3 m | 17.4 m | 16.5 m |
| 18.3 m (60 ft) | 22.0 m | 19.2 m | 18.3 m |
A 16.7 m design truck falls between the 50 ft and 60 ft rows. Wider bays need a shallower apron. The apron is measured from the end of the dock; if columns, canopy posts or parked vehicles are in the way, measure from their outer edge.
Setbacks and what eats the yard
For detached and semi-detached industry, the Selangor manual sets the building back 12.192 m (40 ft) from a road and 7.620 m (25 ft) from the side and rear boundaries. Those are minimums, but if a factory has only 12.192 m in front, a trailer cannot stand square to a front loading door inside the lot. Loading then happens along a deeper side yard, or the truck stands partly on the road. Also check what already stands in the yard: a guard house, a TNB substation, a pump room, covered parking or canopy posts. Each one cuts into the turn.
Terrace and semi-D units
The Selangor manual's minimum lot for a terrace factory is 6.096 m x 24.384 m (20 ft x 80 ft), with one lorry parking bay for every five terrace units. A 24 m deep lot is shorter than the 36.3 m that GP0011-A gives a trailer and its manoeuvring space, so container work at a terrace unit cannot happen fully inside the lot. The truck stands on the service road or back lane, so ask the management or the council whether that is allowed, and look at how neighbours park. The minimum semi-D lot is 18.288 m x 40.233 m, deep enough only if the building leaves a long yard. For a container-heavy operation, start with detached factories for sale in Selangor.
What size loading door and dock does a container need?
- Door: the container door opening is at least 2.337 m wide and 2.261 m high (2.565 m for a high cube). A forklift working inside the box must fit through that, and your shutter must open wider and higher than the container end so the truck can back right up to it.
- Dock height: GP026 recommends a dock height of 1.2 m to 1.32 m, with the dock width matched to the handling equipment.
- Ways to unload: at a raised dock with the container on the trailer, at ground level with a yard ramp, or by lifting the box off with a side-loader or crane. Each needs different space; our specs guide compares them.
- Number of bays: the Selangor manual asks detached and semi-D industry for one lorry space per 929.030 m² (10,000 sq ft) of floor area or at least two, whichever is higher.
You can filter units by container access and loading bays on the spec search page.
What should you measure at a viewing?
Bring a laser measure and walk the route the truck will take, from the highway to the loading door:
- The route in: tight junctions, low bridges, height or weight limit signs, and roads lined with parked trailers between the highway and the gate.
- The road: kerb-to-kerb width outside the gate, any median, one-way rules and lorries parked opposite.
- The gate: clear opening with the gate fully open, headroom under anything overhead, and the width of the drain crossing.
- The turn: a clear area about 30 m across if the truck must turn inside; otherwise, whether it can reverse in safely from the road.
- The yard: depth from the loading door to the boundary or the first obstacle, against the 36.3 m benchmark, and every structure in the way.
- The door and dock: clear width and height, dock height, canopy height against the 4.5 m benchmark.
- The surface: concrete or premix, cracks, ponding and drain covers in the wheel path.
- The papers: the approved layout plan showing lorry parking and loading areas, and, for a shared driveway, who has the right to use it.
- A test run: ask your haulier to drive the route with an empty trailer before you sign, and film it.
For warehouses close to the port, compare units on the Westport warehouse page; our partner site's Westport or Northport checklist covers the choice between the two terminal sides.
Common mistakes
- Trusting "container access" on a listing without a test run by your own haulier.
- Measuring the gate but not the road or the culvert in front of it.
- Planning for 20 ft when your supplier ships 40 ft high cubes.
- Forgetting what is overhead: canopies, cables, gate beams and trees.
- Using the road as the yard: neighbours, traffic and the council will all have a view.
Practical steps: more questions
What is the standard loading bay size in Malaysia?
Selangor's planning manual sets a goods loading area of at least 9.144 m x 7.924 m, and a trailer bay of 4.267 m x 17.983 m with 18.288 m extra for handling. PLANMalaysia's parking guideline uses a 4 m x 18 m trailer bay plus 18.3 m for manoeuvring, 36.3 m in total.
What is the difference between 40ft and 40ft HC?
Both are 12.192 m long and 2.438 m wide. A standard 40 ft container is 2.591 m high and a high cube is 2.896 m, about 0.3 m taller, with a taller door opening of 2.565 m. Check headroom at your gate and canopy for the high cube.
How many kg are in a 40 ft container?
Hapag-Lloyd rates its general purpose 40 ft containers at up to 32,500 kg gross. One 40 ft series it lists weighs 3,700 kg empty and can carry 28,800 kg. The actual rating is marked on each container, and road weight limits apply to the whole truck.
How wide should a factory gate be for a 40 ft container truck?
There is no single figure for every factory gate. PLANMalaysia's heavy vehicle terminal guideline uses 12.0 m entrances and exits, which is a useful benchmark for sites that take trucks all day. A narrower gate can work on a wide road; on a narrow road, test it with your haulier.
Can a 40 ft container truck go into a terrace factory?
Rarely all the way. Selangor's minimum terrace factory lot is 6.096 m x 24.384 m, shorter than the 36.3 m a trailer and its manoeuvring space need under PLANMalaysia's guideline, so the truck usually stands on the road or back lane. Check what the management and the council allow.
The figures here are planning guideline benchmarks, not legal advice; the council and a registered engineer decide what applies to a particular site. Selangor approved a newer 2025 edition of its planning manual in November 2025, sold in print by PLANMalaysia Selangor, so confirm current figures with the council's planning department.
Frequently Asked Questions
Which industrial areas in Selangor can 40 ft container trucks enter?
There is no official list of estates open to 40 ft container trucks; access is decided road by road and lot by lot. FactoryHub's guides point container-heavy users to the Port Klang belt: Pulau Indah and Westport, Northport, Telok Gong, Bukit Raja and Kapar. Selangor's planning manual sets industrial service roads at 20.116 m (66 ft), but parked trailers, tight junctions, low overhead structures and short terrace lots still stop trucks inside good estates. Ask your haulier to run the route to the gate before you sign.
How do I know if a factory has enough space to park a 40 ft container truck?
Measure it: a container trailer needs about 36.3 m of clear length to park or load. PLANMalaysia's parking guideline sizes a trailer bay at 4 m x 18 m and adds 18.3 m for manoeuvring. Measure from the loading door to the boundary or the first obstacle, such as a guard house, substation or canopy post, and check the lorry bays on the approved layout plan. A terrace lot about 24 m deep cannot hold one, so the truck stands on the road; ask the management or the council whether that is allowed.
What size roller shutter does a factory loading door need?
There is no single standard size; size the shutter to what passes through it. For containers, the container door opening is at least 2.337 m wide and 2.261 m high (2.565 m for a high cube), and the shutter must open wider and higher than the container end so the truck can back right up to it. If lorries or forklifts drive inside, it must clear the tallest loaded vehicle or mast; PLANMalaysia uses 4.5 m of headroom for lorries under cover. Measure the clear opening with the shutter fully up.
How many entrances and exits does a factory need?
For people, the building needs at least two separate exits from each storey under by-law 166 of the Uniform Building By-Laws, within travel distances of 30 m for a general factory without sprinklers and 60 m with them. For vehicles there is no fixed number of gates. One gate works if trucks can reverse in safely from the road; two gates let them drive through, because turning round inside needs a clear area about 30 m across. Your architect and Bomba confirm the exits for your building.
Can a factory have separate entrances for workers and lorries?
Yes, where the lot allows it, and it is safer. Container trucks usually reverse in, and on a tight turn they sweep a band about 7.7 m wide, so a separate gate or path for staff and visitors keeps people out of that zone. A detached or corner lot with a wide frontage or two road frontages makes it easiest; a terrace unit usually has one frontage only. If you rent, a new gate needs the landlord's written consent, and check with the council before opening one onto the road.
Which industrial areas are suitable for 40 ft container trucks to go in and out?
Container access depends on the road, gate and yard of each unit more than on the area. Container-heavy users mostly sit in the Port Klang belt (Pulau Indah and Westport, Northport, Telok Gong, Bukit Raja and Kapar), and detached units with their own yard are the easiest to serve, while a trailer rarely fits fully into a terrace lot. The semi-trailer is about 16.7 m long with a minimum turning radius of 13.7 m, so measure the road, gate opening and yard depth, and ask your haulier to run the route before you sign.
How long is a 40 ft container truck?
The container itself is 12.192 m long. With the prime mover, the truck is longer: JKR's semi-trailer design vehicle, used for road design in Malaysia, is 16.7 m long. Since March 2026, open-platform trailers of up to 45 ft are also approved for 40 ft and 45 ft containers on port runs.
What is the turning radius of a container lorry?
JKR's semi-trailer design vehicle has a minimum turning radius of 13.7 m and an inside radius of 6.0 m. In practice it needs a clear circle of about 30 m across to turn round, which is the figure Selangor and PLANMalaysia use for turning circles at industrial dead ends.
FactoryHub is dedicated to helping every client find the right factory or warehouse. To shortlist units a 40 ft truck can actually reach, contact Jason Low (PEA 1478) at 012-288 1834.
