Key Takeaways

  • Factory site selection in Malaysia comes down to seven checks: workers, freight access (highway, port and airport), power, water, flood history, zoning and room to expand. Zoning and power are pass or fail. The rest are trade-offs you weigh by which cost weighs most in your operation.
  • Whether to sit near workers' housing or near the highway depends on your cost mix. The minimum wage is RM1,700 a month for the whole country, so location changes commuting time, staff turnover and hostel needs, not the wage floor.
  • Power takes the longest to fix. In TNB's own planning figures, a new 11 kV supply (1,000 kVA to under 5,000 kVA) takes 6 to 12 months and a 33 kV supply 18 months to 2 years, and both need land on your lot for a switching station.
  • Room to expand is a planning question, not a question of empty land. Every extension needs planning permission and written permission to build from the council. If you rent, get expansion rights in writing, because a tenancy of up to three years is not registered on the title.
  • Moving to another state keeps the minimum wage, TNB as supplier and federal taxes the same. It changes the land office and quit rent, the council and its licences, the water operator and its tariff, and it needs a MIDA amendment if you hold a manufacturing licence.

What factors matter most in factory site selection?

The short answer: check zoning and power first, because no amount of cheap rent fixes a lot where your activity is not allowed or where TNB cannot deliver the load in time. Then rank the trade-offs by money. Write down the monthly costs that location changes for you (payroll and worker transport, haulage, power and water) and let the heaviest line decide where you search.

Factor Pass or fail, or trade-off What decides it Where to verify
Zoning and land title Pass or fail Your activity must fit the land use on the title, the zoning in the local plan and DOE's siting class Title search, council planning department, SISMAPS in Selangor
Power Pass or fail within your timeline Existing TNB supply against your maximum demand now and in five years TNB supply records, a registered electrical engineer
Flood history Pass or fail for heavy machines and high-value stock Floor platform level, past floods, nearby flood works Council or JPS district office, Public InfoBanjir, neighbours, your insurer
Workers Trade-off Headcount, shifts, share of foreign workers Drive the route at shift change, hostel options
Freight access Trade-off Container and lorry trips a month, air shipments Per-trip quotes from hauliers for each address
Water Trade-off, pass or fail for wet processes Daily volume, meter and pipe size Water operator
Room to expand Trade-off Plot ratio, building coverage, setbacks, neighbouring units, lease rights Council planning department, landlord

Price comes last. Compare registered rents and prices only between sites that pass the first two checks, using the JPPH-registered industrial transactions. For which estates suit food, logistics, E&E, chemicals or heavy engineering, see which industrial area suits your industry; this guide covers the decision method that sits on top of that.

Should a factory be near workers' housing or near the highway?

Direct answer: if labour is the location-sensitive cost that weighs most for you (many operators, two or three shifts), choose a site close to where your workers live or can be housed. If haulage is the bigger cost (several container or lorry movements a day), choose a site a short drive from a highway interchange and the port. When both matter, remember that you can bus workers in from a hostel, but you cannot shorten a lorry route.

What the rules say about wages and housing

The minimum wage does not change with the district. Under the Minimum Wages Order 2024 it is RM1,700 a month for the whole country, and it has applied to every employer since 1 August 2025. So moving from Klang to Seremban does not lower the wage floor; what changes is how far people travel and how many stay.

If you employ foreign workers, housing is part of the site decision. JTKSM's Act 446 guidance says an employer of foreign workers must provide accommodation under the 2020 accommodation regulations, every accommodation needs an Accommodation Certificate from the Director General of Labour, applications are made online, operating without one can be fined up to RM50,000, and the employer must report where workers are placed within 30 days.

What to check on site

  1. Drive from the nearest housing areas to the gate at 7 am and at shift change, not at noon.
  2. Check where a staff bus or van can stop and turn inside or beside the lot.
  3. List certified hostels or centralised labour quarters within a short bus ride, and the cost per bed.
  4. Ask neighbouring factories how long they take to fill operator jobs.

District population and labour data are summarised in which Klang Valley industrial area makes hiring easier.

How far should a factory be from the port and the airport?

Direct answer: measure distance in trips and hours, not kilometres. A site 10 minutes further out costs little if you move two containers a month, and a great deal if you move twenty a day.

  1. Count your trips: containers in and out a month (20 ft and 40 ft), local deliveries, and air shipments.
  2. Time the route at the hours your lorries run, including the last stretch inside the estate, where narrow roads and parked cars slow everything down.
  3. Ask two hauliers for a per-trip price from each shortlisted address. The difference multiplied by your monthly trips is the real cost of distance.
  4. Decide which side of the port you use. Port Klang has two main container terminals in different places, Westports on Pulau Indah and Northport, so a site that is close to one can be far from the other. Our partner site sets out five checks before you pick Westport or Northport, and our own Port Klang industrial zones comparison covers the free zone as well.
  5. If you fly goods out, time the drive to KLIA in Sepang the same way.
Site manager timing a container lorry leaving a factory gate towards the highway and port
IllustrationSite manager timing a container lorry leaving a factory gate towards the highway and port

How do you check power and water before you commit?

Power

Ask the owner for the current TNB supply in writing: supply voltage, capacity in kVA or amps, and whether there is a substation on the lot. Then compare it with your maximum demand today and in year five. You can convert a machine list with our factory power calculator.

If your five-year load crosses into a medium voltage supply, the timeline matters more than the tariff. TNB's briefing on getting electricity supply, published by MIDA, gives these typical lead times:

Supply voltage Maximum demand Typical lead time Land for the switching station
11 kV 1,000 kVA to under 5,000 kVA 6 to 12 months 13.0 m x 14.2 m
33 kV 5,000 kVA to 25,000 kVA 18 months to 2 years 30.0 m x 30.0 m
132 kV 25,000 kVA to under 100,000 kVA 3 to 5 years 115 m x 110 m

TNB notes that lead time depends on the distance to its network and the complexity of the site. Its Electricity Supply Application Handbook also requires the applicant to transfer or lease the substation land to TNB at a nominal RM10. In practice, if you expect to pass 1,000 kVA within five years, the lot needs a corner that can be given up for a switching station, which is far easier on a detached lot than in a terrace row.

Water

Water operators and tariffs follow state lines. Air Selangor supplies Selangor, Kuala Lumpur and Putrajaya, and its tariff notice sets non-domestic water at RM3.51 per cubic metre for the first 35 m³ and RM3.83 per cubic metre beyond that, from 1 September 2025, with a separate RM5.31 per cubic metre category for data centres. In Negeri Sembilan the operator is Syarikat Air Negeri Sembilan (SAINS), whose rates are reviewed separately through the national regulator SPAN, so ask SAINS for the current industrial rate. On site, check the meter size, the incoming pipe, the storage tank and the pressure at peak hours, and ask the operator in writing whether a bigger connection is possible if your process uses a lot of water.

How do you check a site's flood history?

Direct answer: ask the authorities, watch the live river data, and inspect the site yourself. Never rely only on the seller's word.

  • Ask the council or the JPS district office. On 11 August 2025 JPS Malaysia and JPS Selangor presented the Flood Hazard Map to the Selangor government. It marks flood-risk areas from historical flood records, hydrological data and topographic analysis, and is meant to guide planning by the authorities, so ask whether the lot falls in a mapped flood-prone area.
  • Watch the nearest river station. Public InfoBanjir shows river levels against Normal, Alert, Warning and Danger thresholds and rainfall from Light (1 to 10 mm) to Very Heavy (over 60 mm). Find the station on the river closest to the estate and check it during a wet week.
  • Check nearby flood works. JPS Selangor links a flood mitigation project dashboard from its site; see whether projects near your shortlist are finished or still running.
  • Inspect. Compare the floor platform with the road and the main drain, look for water lines on walls and roller doors, and ask the guardhouse and neighbours what happened in the last big storm.
  • Price the insurance before you sign. Ask an insurer to quote with flood cover for the exact address.

How do you confirm the zoning before you sign?

Direct answer: three layers must all fit your process. The land use category and express conditions on the title, the zoning in the council's local plan, and the DOE siting class of your activity. Check all three before you commit, not after.

  • Selangor: PLANSelangor's SISMAPS gives councils, developers and the public access to zoning, current land use and a lot and zoning check.
  • The law behind it: under section 19 of the Town and Country Planning Act 1976, no one other than the local authority may carry out development without planning permission. PLANMalaysia notes that this Act applies in the Peninsular states, while Kuala Lumpur has its own planning law.
  • DOE class: the buffer distances for light, medium and heavy activities are tabled in our industry matching guide.

How do you judge room to expand in five years?

Direct answer: work out the floor area you can legally add, not the empty land you can see.

If you buy or already own the land

The Town and Country Planning Act counts any extension, and any increase in the height or floor area of a building, as a building operation that needs planning permission. The Street, Drainage and Building Act 1974 adds that no one may erect a building without the council's prior written permission (section 70), and the same applies to a partition, gallery or loft such as a mezzanine (section 79). Before you buy, ask the council planning department for the plot ratio, building coverage, setbacks and parking and loading rules that apply to the lot, subtract what is already built, and keep space for a TNB switching station, lorry turning, fire engine access and drains. What is left is your real expansion room.

If you rent

Under the National Land Code, a tenancy of up to three years is exempt from registration; terms longer than three years are leases that should be registered. Five years of growth usually outlasts one tenancy, so put these in writing:

  • a renewal option with the rent formula agreed now;
  • a right of first refusal on the adjoining unit or vacant land, if the landlord owns it;
  • the landlord's consent, in principle, to a mezzanine or extension, subject to council approval;
  • permission to sublet surplus space while you grow into it.

How big should you rent if you plan to expand within five years?

Rent the space you will use in years one to three and lock in the next step in writing. Rent the five-year size on day one only when carrying empty space costs less than moving twice. Do the sum with registered figures: JPPH-registered detached factory rents in Klang and Port Klang have a median of RM1.22 psf a month, so every 10,000 sq ft taken ahead of need costs about RM12,200 a month at that median. Set that against a second move: fit-out, machine moving, a TNB upgrade with the lead times above, new licences and overlap rent, all laid out in our factory relocation timeline.

Factory buyer reviewing planning documents with a council officer beside a factory model
IllustrationFactory buyer reviewing planning documents with a council officer beside a factory model

What changes when you move your factory to another state?

Direct answer: the federal rules travel with you; land, council and water matters do not.

Item Stays the same across Selangor, KL and Negeri Sembilan Changes when you move
Minimum wage RM1,700 a month nationwide Nothing
Electricity TNB supplies all of Peninsular Malaysia; the tariff schedule in force from 1 July 2025 to 31 December 2027 applies across the peninsula (TNB news clipping) A new supply application at the new address
Water A different operator and tariff (Air Selangor or SAINS)
Quit rent and land dealings Set by each State Authority under section 101 of the National Land Code; consents go to the new state's land office
Planning and building approvals Act 172 in Selangor and Negeri Sembilan Kuala Lumpur uses its own planning law; each council applies its own local plan
Business licence Issued by the council where the factory stands
Manufacturing licence A change of factory location is an amendment filed on InvestMalaysia; MIDA processes post-licensing applications within 30 days of complete information
Foreign workers' housing A new Accommodation Certificate for any new hostel, and placement reported within 30 days

Registered market figures differ between states too. JPPH-registered deals in the 24 months to August 2026:

Area Detached factory rent Semi-detached factory rent Detached factory median price Detached deals
Klang & Port Klang (Selangor) RM1.22 psf/month RM1.78 psf/month RM14.9 million (RM270 psf of land) 69
Shah Alam (Selangor) RM1.50 psf/month RM2.12 psf/month RM16 million (RM335 psf of land) 20
Nilai, Labu & Enstek (Negeri Sembilan) RM1.56 psf/month RM1.70 psf/month RM13 million (RM176 psf of land) 22
Seremban District (Negeri Sembilan) RM1.31 psf/month RM1.67 psf/month RM13 million (RM169 psf of land) 34
Senawang, Sungai Gadut & Sendayan (Negeri Sembilan) RM1.08 psf/month RM1.61 psf/month RM19 million (RM188 psf of land) 7

Rents are per sq ft of rented floor area a month; sale prices per sq ft are per sq ft of land. The typical unit size differs by area (the registered detached tenancies in Klang centre on about 15,090 sq ft, in Nilai on about 5,080 sq ft), so compare like with like, and treat the Senawang detached median, from 7 deals, with care.

Approvals, title and rules: more questions

Do I need a new manufacturing licence if I move my factory?

If you hold a manufacturing licence, a change of factory location is filed as an amendment through MIDA's InvestMalaysia portal rather than as a new licence. MIDA states that post-licensing applications are processed within 30 days of receiving complete information. Your council business licence, however, has to be obtained from the council where the new factory stands.

Can I check the zoning of an industrial lot online in Selangor?

Yes. PLANSelangor's SISMAPS lets the public check the zoning and current land use of a lot. Confirm the result with the title's land use category and express conditions, and with the council's planning department before you sign.

Practical steps: more questions

How long does TNB take to supply power to a new factory?

It depends on the load. TNB's planning figures put an 11 kV supply for 1,000 kVA to under 5,000 kVA at 6 to 12 months and a 33 kV supply for 5,000 kVA to 25,000 kVA at 18 months to 2 years, with longer times for distant or complex sites. Smaller loads on an existing network are quicker, so ask the owner for the current supply first.

This guide explains public rules and registered data in general terms. It is not legal or tax advice; confirm the position for your lot with the council, the land office and your lawyer.

Frequently Asked Questions

Which industrial area has the best infrastructure?

There is no official ranking, because infrastructure differs from lot to lot even inside one estate. Judge an area on five checks: the peak-hour truck run to the port or your customers, TNB capacity on the lot, water meter size and pressure, drainage and flood history, and road and gate width for 40 ft trailers. In Selangor's managed industrial parks, such as Elmina Business Park and Bandar Bukit Raja IV, a private park manager maintains roads, drains, street lights and security, but you still need to check the specific unit.

How far from a highway should a factory be?

There is no set distance. Measure it in time and trips: if you run several container or lorry trips a day, choose a site a short drive from a highway interchange, and time the route at the hours your lorries run, including the narrow last stretch inside the estate. Ask two hauliers for a per-trip price from each address; the difference times your monthly trips is the real cost of distance. If workers matter more than freight, being near their housing can outweigh highway access.

Are there restaurants and convenience stores near the factory?

It depends on the estate, so check it on site rather than assume. Visit at lunchtime and at shift change, see where workers from neighbouring factories eat and shop, and ask how far they walk or ride. For night shifts, check what is still open late. Selangor's planning manual also asks for a canteen inside the factory of about 2% of the factory floor, so a site with few shops nearby can still feed its staff.

How can I find a factory suitable for production in Selangor?

Start from what your process needs and shortlist only units that pass. First check that the title and local plan allow your activity (light, medium or heavy industry) and that the TNB supply covers your load in amps: both are pass or fail, and power takes the longest to fix. Then check floor loading, clear height, truck access, flood history and travel time for workers. Filter by amps, ceiling height and floor loading on FactoryHub's spec search, or give your brief to Peter Tan or Jason Low.

What makes a good location for a factory?

A good factory location is one where your activity is allowed by the title and the local plan, TNB can supply your load within your timeline, the lot has no flood history that threatens machines or stock, and your workers and lorries can reach it at a cost you can carry. Room to add floor area legally is the next test. Price only separates sites that pass all of these.

What are the 5 factors to consider when choosing a factory location?

For a Malaysian factory the five that most often decide the shortlist are zoning, power, flood history, access for workers and freight, and room to expand. Water joins them for food, beverage, plating and other wet processes. Rent or price is weighed after these.

What are the 7 keys to facility location?

In this guide the seven checks are workers, freight access, power, water, flood history, zoning and room to expand. Zoning and power are pass or fail; the other five are trade-offs ranked by which cost weighs most in your operation.

Is a factory in Negeri Sembilan cheaper to run than one in Selangor?

The minimum wage and TNB's tariff schedule are the same in both states, so the savings come from rent, land price and labour availability, not from wage or electricity rules. JPPH-registered detached factory rents in Seremban District have a median of RM1.31 psf a month against RM1.22 psf in Klang and Port Klang, so the gap depends heavily on the exact area and unit size. Add the extra haulage if your containers still go through Port Klang.

FactoryHub is dedicated to helping every client find the right factory or warehouse. To shortlist sites against these checks, call Peter Tan (REN 12771) at 016-666 6872 or Jason Low (PEA 1478) at 012-288 1834.